17 4ph investment cast

17-4PH Precipitation Hardening Stainless Steel-Casting ...

Alloy 17-4PH (UNS S17400), Type 630, is a chromium-nickel-copper precipitation-hardening martensitic stainless steel with an addition of niobium. 17-4PH combines high strength and hardness with good corrosion resistance.

Martensitic Stainless Steel Investment Casting ...

Martensitic Stainless Steel Alloy Properties Condition Tensile Strength 0.2% Yield Strength % Elongation Range (2.5 cm or 1”) Hardness Range or Max

Stainless Steel Investment Castings - Aero Metals

Stainless steel investment castings are “corrosion-resistant” when used in liquid environments and vapors below 1200°F (650°C) and “heat-resistant” when used above this temperature. There are differences between wrought and cast versions of stainless steel.

Numerical simulation of the solidification microstructure ...

17-4PH stainless steel is the main alloy to be investment cast in this study, where the main alloying components are iron, chromium, nickel and copper, shown in table 1. In the actual casting experiment, two molds, calibration and test were designed as shown in figures 1 and 2 .[PDF]

The Effects of Casting Porosity on the Tensile Behavior of ...

The Effects of Casting Porosity on the Tensile Behavior of Investment Cast 17-4PH Stainless Steel D.F. Susan, T.B. Crenshaw, and J.S. Gearhart (Submitted May 4, 2015; published online June 30, 2015)

The Effects of Casting Porosity on the Tensile Behavior of ...

1) is 15.1 for investment cast 17-4PH in the high-strength H925 condition. The lower strength H1100 condition gives an index of defect susceptibility of only ~5.0. The lower strength H1100 condition gives an index of defect susceptibility of only ~5.0.

Failure analysis of holding yokes made of investment cast ...

Holding yokes made of investment cast 17-4PH stainless steel were too soft (below 20 HRC).Optical microscopy of the parts showed that there is a high fraction of retained austenite after oil quench due to high amount of molybdenum found in parts as an impurity.

Investment Casting | The Casting Company, Inc.

Impeller Oil and Gas Industry 356 Aluminum, and 17-4 17-4 PH Sight Instrument for Military Land Vehicle Universal Joints for Race Cars Benefits of Investment Casting ... Elimination of Material Waste – Investment castings are cast to size, decreasing the amount of machining required.

Effect of porosity on ductility variation in investment ...

The stainless steel alloy 17-4PH contains a martensitic microstructure and second phase delta ({delta}) ferrite. Strengthening of 17-4PH is attributed to Cu-rich precipitates produced during age hardening treatments at 900-1150 F (H900-H1150). For wrought 17-4PH, the effects of heat treatment and ...

Failure analysis of holding yokes made of investment cast ...

Holding yokes made of investment cast 17-4PH stainless steel were too soft (below 20HRC). Optical microscopy of the parts showed that there is a high fraction of retained austenite after oil ...

The Effects of Casting Porosity on the Tensile Behavior of ...

Abstract. The effect of casting porosity on the mechanical behavior of investment cast 17-4PH stainless steel was studied as well as the effect of heat treatment on the alloy’s sensitivity to casting defects.

Cast 17-4PH Heat Treat - Hardness vs Yeild Strength ...

eng-tips› …› Steel and Stainless engineering ForumFeb 14, 2007· Here is a quote from MIL-HDBK-5J regarding 17-4PH castings "Alloy 17-4PH castings are produced in sand molds, investment molds, and by centrifugal casting. While 17-4PH has good castability, it is subject to hot-tearing, so heavy X or T sections, sharp corners, and

Investment Castings For Aerospace - signicast

Aerospace Investment Castings 8620, 17-4PH, 15-5PH & Aluminum. At Signicast, we pour a wide variety of ferrous and non-ferrous alloys including 300 stainless steels that can be cast almost as thin as aluminum. Then, utilizing soluble or ceramic core technologies, we can produce complex interior features or geometries. ...

Alloy Shrinkage Factors for the Investment Casting of 17 ...

Abstract. In this study, alloy shrinkage factors were obtained for the investment casting of 17-4PH stainless steel parts. For the investment casting process, unfilled wax and fused silica with a zircon prime coat were used for patterns and shell molds, respectively.

17-4 Stainless Steel | 630 Alloy

17-4 Precipitation Hardening also known as Type 630 is a chromium-copper precipitation hardening stainless steel used for applications requiring high strength and a moderate level of corrosion resistance.

A study on the investment casting of 17-4PH stainless ...

AbstractThe complex shape of helical impellers in centrifugal pumps increases the difficulty of investment casting. Determining means of predicting the form and location of defects in order to prevent the formation of defects is crucial to the casting process. This study employed AnyCasting to conduct flow analysis on the moulding of 17-4PH stainless steel impellers in centrifugal pumps.Published in: Materials Research Innovations · 2015Authors: P H Huang · M J GuoAffiliation: University of Science and Technology Sana aAbout: Investment casting · Impeller

17-4PH stainless steel investment casting, China ...

As the leading China investment casting manufacturer, Qinhuangdao ANYE can provide precipitation-hardening stainless steel investment casting in accordance with client’s requirements. The main material is 17-4PH stainless steel.

Alloy Shrinkage Factors for the Investment Casting of 17 ...

In this study, alloy shrinkage factors were obtained for the investment casting of 17-4PH stainless steel parts. For the investment casting process, unfilled wax and fused silica with a zircon ...

Physical and mechanical properties of cast 17-4 PH ...

Abstract. The physical and mechanical properties of an overaged 17-4 PH stainless steel casting have been examined. The tensile and compressive properties of cast 17-4 PH are only influenced to a slight degree by changing test temperature and strain rate.Authors: H J RackAbout: Electron microscope · Thermal conductivity · Chromium · Fracture toughness · Young'…

Failure analysis of holding yokes made of investment cast ...

Holding yokes made of investment cast 17-4PH stainless steel were too soft (below 20 HRC).Optical microscopy of the parts showed that there is a high fraction of retained austenite after oil quench due to high amount of molybdenum found in parts as an impurity.

Casting - Metal Products, Inc.

Aluminum Die Casting. There are many reasons aluminum is the most commonly cast non-ferrous metal in the world. It’s light, strong, corrosion resistant, non-staining, highly conductive, non-magnetic, accepts many finishes and is cost effective.

Hot Products

We are here to serve you!

Reply to technical consultation Provide design solution Dispatch engineers domestically/abroad Handle complaints thoroughly Systematic training Trouble judgment &amo; removal